Corrosion Exposure on U.S. Coastal Installations: Above Grade and Below
Atmospheric and soil corrosion exposure at U.S. military installations, mapped.
The problem, in two parts
Corrosion of steel and reinforced concrete on military installations is driven by two separate environments, and most facilities are managed as if there were only one.
Atmospheric exposure. The Department of Defense rates every installation by Environmental Severity Classification using the ISO 9223 categories C1 through CX, driven by time of wetness, salt-air chloride deposition, and sulfur dioxide. The rating predicts corrosion of exposed steel and of reinforcing steel in above-grade concrete: aprons, piers, wharves, seawalls, parking structures, and exterior frames. The Gulf Coast, Florida, the Atlantic seaboard, and the Southern California coast rate C4 and C5. The interior rates C1 and C2.
Soil exposure. Buried steel and below-grade concrete corrode by a different mechanism, governed by soil resistivity, chlorides, sulfates, pH, and moisture. USDA-NRCS rates every soil map unit in the country for risk of corrosion to uncoated steel and to concrete, and wet, fine-textured, saline soils rate High: the Gulf Coastal Plain, the Mississippi Valley, the Florida peninsula, the Atlantic tidal margins, the Texas Blackland, the Central Valley, and the alkaline basins of the desert Southwest. Foundations, piers, tiebacks, utility structures, and slab reinforcement in these soils corrode regardless of what the air is doing above them.
Why it matters on an installation
The two maps overlap on the coasts. Installations from Corpus Christi around the Gulf to Key West, up the Atlantic to Norfolk, and along the Pacific from San Diego to Ventura sit in the highest atmospheric category and on High-rated soils at once, so reinforced concrete is attacked from both faces: chloride from salt air on exposed surfaces, chloride and sulfate from groundwater and soil below. UFC 1-200-01 requires designers to account for the ESC rating in materials and protection; the DoD Corrosion Prevention and Control Source carries the criteria. Three things follow for anyone planning or specifying repair:
- Deterioration is further along than the surface shows. Rusting reinforcement expands to several times its volume before concrete cracks; delamination and section loss precede visible spalling by years. Visual inspection alone under-scopes the repair.
- Repairs specified to the wrong environment fail early. A patch that does not treat the reinforcement and the chloride around it fails at its perimeter. Underpinning steel chosen without regard to soil resistivity loses section in the ground.
- The interior is not exempt. Installations rated C1 or C2 atmospherically still sit on High-rated soils, and below-grade corrosion there is under-inspected precisely because the atmospheric rating is low.
What we do
Bristol Restoration, Inc. is a Service-Disabled Veteran-Owned Small Business providing corrosion condition survey, structural concrete repair, and foundation underpinning on federal installations, working as a subcontractor to prime contractors and job order contract holders, and directly on small task orders below bonding thresholds. Mobile survey and repair crews, with local hiring for term work.
Inspection and corrosion mapping
Field survey of concrete elements to locate active and incipient corrosion before spalling: half-cell potential per ASTM C876, cover meter, delamination sounding, chloride profiling, and carbonation testing, delivered as a map of the structure with repair quantities. No bonding, no excavation; the basis for prioritizing and scoping repair task orders. Where a stamped assessment is required, we perform the field work under a licensed A/E firm.
Concrete corrosion repair
Spall and delamination repair to ICRI 310.1R and ACI 562: removal to sound concrete with clearance behind the steel, reinforcement cleaned or supplemented, corrosion-inhibiting treatment, and section restored with compatible repair mortar. Embedded galvanic anodes at repair perimeters stop the incipient-anode failure that undoes most patches.
Crack repair
Epoxy injection for dormant structural cracks; polyurethane injection for leaking cracks below grade and in water-retaining structures; route-and-seal for moving cracks. Width, moisture, and movement are documented before the method is chosen.
CFRP encapsulation and strengthening
Most corrosion repair ends with a patch, and the patch is the weak point. A carbon-fiber layer over the completed repair encapsulates the patch, blocks moisture and chloride at the bond line, and confines it so a debond cannot become a spall, while adding flexural, shear, or confinement capacity per ACI 440.2R. Field design by our construction lead; load calculations by a licensed engineer; verification protocol set jointly.
Resurfacing and protective overlays
Polymer-modified overlays, traffic-bearing membranes, and penetrating sealers to restore the wearing surface and stop chloride re-entry after repair. Surface preparation to the manufacturer's profile, with bond and moisture verified before placement.
Below-grade waterproofing and water-stop
Positive-side membranes where excavation is possible and negative-side crystalline systems where it is not; hydrophilic and injectable water-stops at joints; polyurethane injection for joints already leaking; penetration sealing.
Deep foundation systems
Four distinct systems, selected by load, soil, and access: micro-piles, Stelcor drilled-in displacement piles (certified installer), push piers, and helical piers, each also installable as hillside tiebacks where rotated. Installed with Word rock drills on wheeled tool carriers and Geax drilling rigs. On occupied buildings the constraint is access, not headroom: our crews have ramped a rig 30 feet into a hotel basement and craned a 22,000-pound rig through an atrium roof. Steel elements are protected to site soil conditions.
Federal installation experience: Nellis Air Force Base, 2018
A ruptured water main inside a U.S. Air Force Weapons School classroom facility eroded the bearing soil, settled the foundation unevenly, and fractured the CMU walls; the building was evacuated. It sat directly adjacent to an active taxiway with F-16s taxiing and running up throughout the day: jet-wash, zero tolerance for FOD, and a security perimeter that limited equipment, staging, and hours. Foundation Tech, Inc., with Jerold Bronstrup as principal, stabilized and lifted the structure on helical piles installed with small equipment inside those constraints, with no interruption to flight operations, and returned the building to service. Bristol Restoration brings the same crew leadership and the same working discipline to installation task orders.

Who you'd be working with
Jon F. Berry, Colonel, USAF (Ret.), President & CEO. Thirty years in the Air Force: master air battle manager, combat veteran of four named operations, commander of the 1st Air Support Operations Group at Joint Base Lewis-McChord, and J3 for Joint Region Marianas. Since retiring: business development lead for Air Force and Space Force programs at Teledyne FLIR, and company principal for nine emergency and rapid-response deployments in 2024 to 2026. Jon is the point of contact for primes and contracting officers and owns contract administration, schedule, reporting, and installation coordination on every task order.
Jerold S. Bronstrup, Vice President and Director of Construction. Has run construction and foundation repair companies since 2002; Responsible Managing Officer of Foundation Tech, Inc. (CA CSLB #991221, AZ ROC #354312). Underpinning, micro-piles, slab stabilization, and structural concrete repair for commercial, institutional, and public-sector owners, including Nellis AFB; lead on structural runway repairs at Beijing Capital International Airport (2015); ten years as a Fannie Mae rehabilitation contractor and a VA-approved contractor modifying homes for disabled veterans (2009 to 2011). Jerold owns scope, means and methods, crew supervision, and quality of the repair.
Jon administers, Jerold builds. One point of contact for contract matters, one for field execution.
How we work with primes and JOC holders
- Scopes are self-performed by our crews; we don't broker the work.
- Mobilization: survey crews travel light and mobilize from the nearest home base on short notice; emergency repair is scoped and priced per task order from the closest base; programmed JOC task orders mobilize to the task-order schedule, typically 30 to 60 days from notice to proceed. Term work is staffed with local hires under our supervision.
- Licensed in California, CSLB #1141326, Class B General Building. Federal enclave work performed under FAR-based subcontracts; additional state licensing obtained as required by the prime.
- SDVOSB and VOSB, SBA VetCert certified January 2026. CAGE 14GB7. UEI KJXDXNBN8FW5. Subcontracts with us count toward the prime's SDVOSB goal.
- Task orders sized to our current bonding program, with capacity growing on performance. Most survey, concrete repair, and underpinning task orders fall below the Miller Act threshold; where a bond is required, we provide it. Bonding and insurance certificates on request.
- Past performance: VA accessibility modifications for disabled veterans (2009 to 2011); Fannie Mae SAM rehabilitation contractor (2008 to 2018); Nellis AFB Weapons School facility (2018); historic Bank of America bank building corrosion survey, Alameda (2020); Gerdau foundry machinery pedestal (2018); nine emergency and rapid-response deployments, NM/TX/FL (2024 to 2026). Details on request.
What we don't do
Cathodic protection design and installation, protective coatings programs, new-construction concrete, and stamped engineering assessments. We team with the firms that do.
Contact
Jon F. Berry, President & CEO, (360) 742-9796, Jberry@bristolrestoration.com
Jerold S. Bronstrup, Vice President and Director of Construction, (661) 816-6949, Jbronstrup@bristolrestoration.com
CAGE 14GB7 | UEI KJXDXNBN8FW5
Standards referenced: ISO 9223; DoD Environmental Severity Classification (Whole Building Design Guide); UFC 1-200-01; USDA-NRCS National Soil Survey Handbook Part 618; ASTM C876; ICRI 310.1R; ACI 562; ACI 440.2R; Tilly and Jacobs (2007), Concrete Repairs: Performance in Service and Current Practice, CONREPNET. Map sources: DoD ESC; USDA-NRCS SSURGO ratings as mapped in Folkman (2018), Utah State University. Maps are illustrative and not for design use. Installation locations are approximate.
